+ ESE Air Terminal
- VAJRA Series
- PLUS Series
- Saint-Elmo Series
- CIRRUS Series
+ ESE Air Terminal
- X-TRAP
- Prevectron Series
- griffin Series
- Elechippo Series
+ Bipolar Air Terminal
+ Surge Counter
Home > Products > LIGHTNING ROD > Surge Counter

surge arrester

Surge current counter
Surge current counter
ALP LC 1500(7.5 X 10.5 X 6.5)
surge arrester
Surge current counter specs and features(ALP LC 1500)
The test current for this lightning metering device is 1KA(8/20 us) and it can measure the max current of 100kA.
This is an outdoor waterproof product that does not required external power supplies.
It is light weighted and fixed on the ground wire or the conduction wire. Easy to install.
surge arrester
How to install this surge current counter(ALP LC 1500)
ALP LC 1500 or ALP D9 is not directly connected to the conduction wire.
As shown in the figure, simply attach it to the conduction wire. It will automatically detect the guided power and start operating.
As shown in Figure 1, the surge counter should be connected to the conduction wire.
As shown in the figure, use the band mounted on the product to attach it to the conduction wire. Figure 2 is a top view of Figure 1.
It is very easy to install. You can change installation in accordance with the site condition.
Surge current counter
ALP D9(6.5 X 4.8 X 4.3)
surge arrester
Surge current counter specs and features(ALP D9)
It operates in the range of 3kA to 100kA.
Using the counter window, you can check the number of lightning strikes. (Size marked below the photo: 6.5 x 4.8x4.3)
The test current for this lightning metering device is 1KA(8/20 us) and it can measure the max current of 100kA.
This product does not required external power supplies.
It is light weighted and fixed on the ground wire or the conduction wire. Easy to install.
How to install this surge current counter(ALP LC D9)
ALP LC 1500 or ALP D9 is not directly connected to the conduction wire.
Use the fixing bracket to fix the product to the conduction wire.
This lightning metering device(LC D9) should be installed on the conduction line with a length of 1 to 1.2 meter.
Install it in a place where it is easy to inspection.
Must not expose it directly to the sunlight.
Cautions
- Do not apply external impacts.
- Do not place a strong magnetic near it.
Surge current counter
(lightning striker recorder)
surge arrester
Surge current counter specs and features(lightning strike recorder)
The test current is 1.5kA. The max current of 220kA can be measured
Functional check of the broadband lightning rod, Elechippo.
Water proof polycarbonate case
No external power supply required.
Simple installation - just tie it to the conduction wire with an SUS band.
surge arrester
Reasons for installation of a surge current counter and its operational principle(lightning strike recorder)
Reasons for installation
According to the application standards of a lightning rod, a lightning rod should be visually checked for a building. However, this is almost impossible.
Therefore, it is desirable to install a surge current counter and check the number of lightning strikes.
Operational principle
A surge current counter operates by excessive impulse currents generated by lightning strikes.
Each time it passes through the surge counter, it is counted.
PrimeSolution l power surge protectors l lightning rods l surge protection device l TVSS l surge arrester l Sitemap
ADDRESS (Main office/factory)
Rm. 609 Suwon advanced venture valley, 958 Gosaek-dong Gwonseon-gu Gyeonggi-do
TEL. 82-31-8007-6150   FAX. 82-31-8007-6158   E-mail: prim0701@primesolution.co.kr
Copyrightⓒ 2003 by Prime solution co.,ltd. All Right Reserved.